How To Get Rubber Hose On Fitting

Download Commodity

Download Commodity

Spinous fittings are great for connecting all kinds of flexible tubing together, but they tin can sure put up a fight when you lot try to insert them! That tight fight is exactly why they work so well, though, and so don't surrender. There are some easy tricks that make getting those spinous fittings securely inside the tubing less of a headache and assistance ensure a proper seal.

1. 1

   Fill a cup with hot water. Cascade hot water into the loving cup straight from a faucet or heat up some h2o in the microwave or on the stove, but not until it's boiling. Be careful not to burn yourself while y'all're doing this.^[1]

   • If y'all have a microwaveable mug, make full it up with h2o as if you lot're going to make tea and microwave information technology using the beverage setting on a microwave to warm it upwards to a practiced temperature.

2. ii

   Stick the terminate of the tubing into the hot water for 10-20 seconds. This warms the tubing up then information technology expands and makes it easier to push the fitting in. Once the tubing cools down over again, it will contract around the fitting for a squeamish tight seal.^[2]

   • You might have to experiment with the verbal amount of time yous leave the finish of the tubing in the hot water. Depending on the temperature of the water and the thickness and limerick of your tubing it may have longer than 10-20 seconds.

   Advertisement

3. 3

   Button the plumbing fixtures into the tubing by wiggling it into place. Stick the tip of the barbed plumbing fixtures into the open up terminate of the tubing that you only heated up. Jerk the fitting using back and along and upwardly and downward motions, while simultaneously pushing hard, until it's all the way within the tubing.^[3]

   • Avoid twisting the fitting into place. This can cause your tubing to kink while yous're forcing the plumbing equipment in.
   • Check to make sure that the border of the tubing is right up against the stop point on the spinous fitting. If you lot see a gap, keep wiggling and pushing the fitting in further.

4. 4

   Slide the hose clamp over the tubing and tighten information technology with a screwdriver. Skid the band over the end of the fitting until it's sitting on the end of the tubing, virtually in the heart of where the barbs are within of the tubing. Hold the ring in place and employ a screwdriver to plow the fastening screw clockwise until it's equally tight equally you can get it.^[4]

   • Don't try to tighten the hose clench by hand. You won't exist able to become a tight enough seal.

Advertisement

1. one

   Ensure that your tubing is made of a flexible safety or plastic material. Barbed fittings are merely meant to work with soft, flexible tubing. Don't try to utilize them with whatever hard, rigid tubing.^[five]

   • Examples of compatible flexible materials are polyurethane, silicone, nylon, and PVC.
   • Flexible tubing that carries liquids, such every bit in drinkable dispensers or irrigation systems, is typically connected using barbed fittings.

2. ii

   Cull a barbed plumbing equipment that matches the inside diameter of your tubing. Look at the printed numbers on the sides of your tubing for the within diameter, or "ID." Use a spinous fitting with a diameter that matches the ID of your tubing exactly, or information technology won't fit properly.^[6]

   • For case, if the internal diameter of your tubing is 1.25 in (3.two cm), use a barbed fitting with a diameter of one.25 in (3.2 cm).
   • If you can't find the ID of your tubing printed on the sides, use a ruler or record mensurate to measure across the mouth of the tubing from one inside wall to the other.

3. 3

   Go a stainless steel hose clench that's wider than the tubing. Check the printed numbers on your tubing for the outside diameter, or "OD." Pick a hose clench that is close to matching the size of the outside diameter, but at least ¹⁄₈  in (0.32 cm) bigger, and so it fits over the tubing.^[vii]

   • Stainless steel hose clamps are the all-time selection for most flexible tubing applications because they won't corrode due to wet.

Advertisement

Ask a Question

200 characters left

Include your e-mail address to get a message when this question is answered.

Submit

Advertisement

• Spinous fittings are useful for connecting flexible tubing that carries water, such as in drip irrigation systems.^[8]

Thank you for submitting a tip for review!

Advertisement

• Exist conscientious not to burn yourself when you're filling a loving cup with hot water.

• Don't try to twist barbed fittings into place or y'all might cause a kink in your flexible tubing.

Advertisement

Things Y'all'll Need

• Cup
• Hot water
• Spinous fitting
• Flexible tubing
• Stainless steel hose clamp
• Screwdriver

About This Article

Thanks to all authors for creating a folio that has been read 16,042 times.

Did this article help yous?

Source: https://www.wikihow.com/Insert-Barbed-Fittings

Share this post